(a) Applicability: This Section applies to onshore steel transmission pipeline segments with a maximum allowable operating pressure of greater than or equal to 30 percent of the specified minimum yield strength and are located in:
(1) A Class 3 or Class 4 location; or
(2) A moderate consequence area as defined by Section 255.3 of this Part, if the pipeline segment can accommodate inspection by means of an instrumented inline inspection tool (i.e., ‘‘smart pig’’).
(3) This Section does not apply to a pipeline segment located in a high consequence area as defined by Section 255.903 of this Part.
(b) General –
(1) Initial assessment. An operator must perform initial assessments in accordance with this Section based on a risk-based prioritization schedule and complete initial assessment for all applicable pipeline segments no later than July 3, 2034, or as soon as practicable but not to exceed 10 years after the pipeline segment first meets the conditions of Section 255.710(a) of this Part (e.g., due to a change in class location or the area becomes a moderate consequence area), whichever is later.
(2) Periodic reassessment. An operator must perform periodic reassessments at least once every 10 years, with intervals not to exceed 126 months, or a shorter reassessment interval based upon the type of anomaly, operational, material, and environmental conditions found on the pipeline segment, or as necessary to ensure public safety.
(3) Prior assessment. An operator may use a prior assessment conducted before July 1, 2020 as an initial assessment for the pipeline segment, if the assessment met the transmission pipeline integrity management requirements of this Part for in-line inspection at the time of the assessment. If an operator uses this prior assessment as its initial assessment, the operator must reassess the pipeline segment according to the reassessment interval specified in Paragraph (b)(2) of this Section calculated from the date of the prior assessment.
(4) MAOP verification. An integrity assessment conducted in accordance with the requirements of Section 255.624(c) of this Part for establishing MAOP may be used as an initial assessment or reassessment under this Section.
(c) Assessment method. The initial assessments and the reassessments required by Paragraph (b) of this Section must be capable of identifying anomalies and defects associated with each of the threats to which the pipeline segment is susceptible and must be performed using one or more of the following methods:
(1) Internal inspection. Internal inspection tool or tools capable of detecting those threats to which the pipeline is susceptible, such as corrosion, deformation and mechanical damage (e.g., dents, gouges and grooves), material cracking and cracklike defects (e.g., stress corrosion cracking, selective seam weld corrosion, environmentally assisted cracking, and girth weld cracks), hard spots with cracking, and any other threats to which the covered segment is susceptible. When performing an assessment using an in-line inspection tool, an operator must comply with Section 255.493 of this Part;
(2) Pressure test. Pressure test conducted in accordance with the testing requirements of this Part. The use of the testing requirements of this Part is appropriate for threats such as internal corrosion, external corrosion, and other environmentally assisted corrosion mechanisms; manufacturing and related defect threats, including defective pipe and pipe seams; and stress corrosion cracking, selective seam weld corrosion, dents and other forms of mechanical damage;
(3) Spike hydrostatic pressure test. A spike hydrostatic pressure test conducted in accordance with Section 255.506 of this Part. A spike hydrostatic pressure test is appropriate for time-dependent threats such as stress corrosion cracking; selective seam weld corrosion; manufacturing and related defects, including defective pipe and pipe seams; and other forms of defect or damage involving cracks or crack-like defects;
(4) Direct examination. Excavation and in situ direct examination by means of visual examination, direct measurement, and recorded nondestructive examination results and data needed to assess all applicable threats. Based upon the threat assessed, examples of appropriate non-destructive examination methods include ultrasonic testing (UT), phased array ultrasonic testing (PAUT), Inverse Wave Field Extrapolation (IWEX), radiography, and magnetic particle inspection (MPI);
(5) Guided Wave Ultrasonic Testing. Guided Wave Ultrasonic Testing (GWUT);
(6) Direct assessment. Direct assessment to address threats of external corrosion, internal corrosion, and stress corrosion cracking. The use of use of direct assessment to address threats of external corrosion, internal corrosion, and stress corrosion cracking is allowed only if appropriate for the threat and pipeline segment being assessed. Use of direct assessment for threats other than the threat for which the direct assessment method is suitable is not allowed. An operator must conduct the direct assessment in accordance with the requirements listed in Section 255.923 of this Part and with the applicable requirements specified in Sections 255.925, 255.927 and 255.929 of this Part; or
(7) Other technology. Other technology that an operator demonstrates can provide an equivalent understanding of the condition of the line pipe for each of the threats to which the pipeline is susceptible. An operator must notify the Department in advance of using the other technology in accordance with Section 255.18 of this Part.
(d) Data analysis. An operator must analyze and account for the data obtained from an assessment performed under Paragraph (c) of this Section to determine if a condition could adversely affect the safe operation of the pipeline using personnel qualified by knowledge, training, and experience. In addition, when analyzing inline inspection data, an operator must account for uncertainties in reported results (e.g., tool tolerance, detection threshold, probability of detection, probability of identification, sizing accuracy, conservative anomaly interaction criteria, location accuracy, anomaly findings, and unity chart plots or equivalent for determining uncertainties and verifying actual tool performance) in identifying and characterizing anomalies.
(e) Discovery of condition. Discovery of a condition occurs when an operator has adequate information about a condition to determine that the condition presents a potential threat to the integrity of the pipeline. An operator must promptly, but no later than 180 days after conducting an integrity assessment, obtain sufficient information about a condition to make that determination, unless the operator demonstrates that 180 days is impracticable.
(f) Remediation. An operator must comply with the requirements in Sections 255.485, 255.711 and 255.713 of this Part, where applicable, if a condition that could adversely affect the safe operation of a pipeline is discovered.
(g) Analysis of information. An operator must analyze and account for all available relevant information about a pipeline in complying with the requirements in Paragraphs (a) through (f) of this Section.